GETEROSTRUKTURALI QOPLAMALARNING ELASTIK MODULI VA YOPISHQOQLIGI O‘RTASIDAGI KORRELYATSIYA
Xojimatov U. T.
Annotatsiya
Mazkur maqolada PVD usuli bilan po‘lat asoslarga yotqizilgan 12 ta turli geterostrukturali qoplama (monoqatlam, ikkiqatlam, ko‘pqatlamli va nanolaminat tizimlar) tahlil qilingan, ularning elastik moduli E (nanoindentirlash usuli, GOST R 8.748-2011) va kritik adgeziya yuklamasi Lc₂ (skratch-test, ASTM C1624-05) aniqlangan. Tahlil shuni ko‘rsatdiki, E va Lc₂ o‘rtasida kuchli manfiy chiziqli bog‘liqlik mavjud (Pearson r = –0,963, p < 0,001), bu mikrostrukturaning monoqatlamdan nanolaminatga o‘tishi bilan kuzatiladi: monoqatlamlar uchun E = 390–425 GPa, Lc₂ = 30–35 N; nanolaminatlar uchun E = 308–335 GPa, Lc₂ = 64–72 N.
Adabiyotlar
- Holleck H., Schier V. Multilayer PVD coatings for wear protection // Surface and Coatings Technology. – 1995. – Vol. 76-77. – P. 328–336. DOI: 10.1016/0257-8972(95)02555-3.
- PalDey S., Deevi S. C. Single layer and multilayer wear resistant coatings of (Ti,Al)N: A review // Materials Science and Engineering A. – 2003. – Vol. 342, No. 1-2. – P. 58–79. DOI: 10.1016/S0921-5093(02)00259-9.
- Holmberg K., Matthews A. Coatings Tribology: Properties, Mechanisms, Techniques and Applications in Surface Engineering. – 2nd ed. – Amsterdam: Elsevier, 2009. – 576 p.
- Musil J. Hard nanocomposite coatings: Thermal stability, oxidation resistance and toughness // Surface and Coatings Technology. – 2012. – Vol. 207. – P. 50–65. DOI: 10.1016/j.surfcoat.2012.05.073.
- Vepřek S., Reiprich S. A concept for the design of novel superhard coatings // Thin Solid Films. – 1995. – Vol. 268, No. 1-2. – P. 64–71. DOI: 10.1016/0040-6090(95)06695-0.
- Bull S. J. Failure modes in scratch adhesion testing // Surface and Coatings Technology. – 1991. – Vol. 50, No. 1. – P. 25–32. DOI: 10.1016/0257-8972(91)90188-3.
- Leyland A., Matthews A. On the significance of the H/E ratio in wear control: a nanocomposite coating approach to optimised tribological behaviour // Wear. – 2000. – Vol. 246, No. 1-2. – P. 1–11. DOI: 10.1016/S0043-1648(00)00488-9.
- Mayrhofer P. H., Mitterer C., Hultman L., Clemens H. Microstructural design of hard coatings // Progress in Materials Science. – 2006. – Vol. 51, No. 8. – P. 1032–1114. DOI: 10.1016/j.pmatsci.2006.02.002.
- Wang Q., Zhou F., Ding X., et al. Microstructure and properties of CrN/AlN multilayer coatings deposited by reactive magnetron sputtering // Applied Surface Science. – 2013. – Vol. 280. – P. 154–161. DOI: 10.1016/j.apsusc.2013.04.116.
- Bull S. J., Berasetegui E. G. An overview of the potential of quantitative coating adhesion measurement by scratch testing // Tribology International. – 2006. – Vol. 39, No. 2. – P. 99–114. DOI: 10.1016/j.triboint.2005.04.013.
- Lichinchi M., Lenardi C., Haupt J., Vitali R. Simulation of Berkovich nanoindentation experiments on thin films using finite element method // Thin Solid Films. – 1998. – Vol. 312, No. 1-2. – P. 240–248. DOI: 10.1016/S0040-6090(97)00739-6.
- Oliver W. C., Pharr G. M. Measurement of hardness and elastic modulus by instrumented indentation // Journal of Materials Research. – 2004. – Vol. 19, No. 1. – P. 3–20. DOI: 10.1557/jmr.2004.19.1.3.
- GOST R 8.748-2011. Метрологическое обеспечение измерений твёрдости методом инструментального индентирования. Часть 1. Метод испытаний. – Moskva: Standartinform, 2012. – 28 b.
- ASTM C1624-05. Standard Test Method for Adhesion Strength and Mechanical Failure Modes of Ceramic Coatings by Quantitative Single Point Scratch Testing. – West Conshohocken: ASTM International, 2015. – 29 p.
- ISO 14577-1:2015. Metallic materials - Instrumented indentation test for hardness and materials parameters - Part 1: Test method. – Geneva: ISO, 2015. – 46 p.